manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 88 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 88

Operation

88

Instructions for Use Fabius MRI SW 3.n

Setting Vaporizer Concentration

Refer to the appropriate Instructions for Use for the 
vaporizer being used. Vapor 2000 is shown and 
described below.

For the Dräger Interlock 2 system:

z

Ensure that the vaporizer is properly seated.

1

Lock the unused vaporizer by moving the selec-
tor lever completely towards it. For example, to 
lock the left vaporizer, move the lever to the left.

2

With the handwheel set to »

T

« position on the 

unlocked vaporizer, press the button and 
engage the handwheel at »

0

«. Wait five sec-

onds for the pressure to balance.

3

Press the button and turn the handwheel coun-
terclockwise to set the required anesthetic gas 
concentration.

z

Regularly check the filling level on the sight 
glass. When reaching the minimum mark, fill the 
vaporizer with anesthetic agent.

For the Dräger Auto Exclusion system:

z

Close any open vaporizers.

z

Ensure that the vaporizer is properly seated.

1

With the handwheel set to »

T

« position, press 

the button and engage the handwheel at »

0

«. 

Wait five seconds for the pressure to balance.

2

Press the button and turn the handwheel coun-
terclockwise to set the required anesthetic gas 
concentration.

z

Regularly check the filling level on the sight 
glass. When reaching the minimum mark, fill the 
vaporizer with anesthetic agent.

041

1

2

3

072

1

2

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments