manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 177 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 177

Instructions for Use Fabius MRI SW 3.n

177

Cleaning

Other

AGS scavenging 
system

Daily

Reprocessing according to appropriate Instructions for Use.

Suction system and 
suction bottle 
assembly accessories

Daily

Reprocessing according to appropriate Instructions for Use.

1) It is generally recommended to perform a pre-cleaning under running water for approx. 5 minutes. 

For dried soiling an additional pre-cleaning step using an ultrasonic bath is recommended. The addition of a quaternary 
ammonium compound supports the cleaning performance effectively (e. g. Gigasept AF). Perform pre-cleaning in the ultra-
sonic bath for approx. 15 minutes. Afterwards rinse under clear running water for approx. 5 minutes (waste water must be 
free of visible cleaning residues).

2) Use mild alkaline or neutral cleaner
3) Use disinfectants based on aldehydes and quaternary ammonium compounds.
4) Do not use any agents containing alcohol.
5) After the machine cleaning and disinfection, a hot steam sterilization is required to dry the breathing system. Insufficient 

drying of the control areas found in the valve plate can lead to an adverse effect on the functions of the medical device or 
to its failure!

6) Valves, ventilator cover and AGS sleeve: Make sure that the cleaning and rinsing liquids can flow in the opening direction 

of the valve.

7) Remove any water which may have accumulated in the ventilator diaphragm. Large quantities of condensed water can 

negatively effect the operation of the device and lead to failure of the medical device!

Fabius MRI 
components which 
can be reprocessed

Recommen-
ded 
reprocessing 
intervals

Manual pre-
cleaning

1)

Machine 
cleaning and 
thermal 
disinfection

2)

Manual disinfection

3)

Hot steam 
sterili-
zation 

Surface 
disinfection

Immersio
n bath 
disinfec-
tion

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments