manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 132 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 132

Configuration

132

Instructions for Use Fabius MRI SW 3.n

Configuration Functions in Standby 
Mode

The configuration functions available in Standby 
include calibrations, system tests, and the manage-
ment of default settings.

To access Standby mode:

1

Press the »

Standby

« key.

The waveform window is replaced by a confirma-
tion message and the instruction to shut off flow. 
The LED on the Standby key starts blinking and will 
remain blinking until Standby is confirmed.

z

Confirm the mode change. The ventilator enters 
Standby mode, the Standby screen replaces the 
previous screen, and the Standby LED stops 
blinking and remains on.
The following soft key labels appear at the bot-
tom of the Standby screen:

– »

Run System Test

«

– »

Calibrate Flow Sensor

«

– »

Calibrate O2 Sensor

«

– »

Leak / Compl Test

«

– »

Access Alarm Log

«

– »

Restore Site Defaults

«

z

Turn off fresh gas flow.

NOTE

If confirmation does not occur within 15 seconds, 
the ventilator remains in the previous mode and 
the waveform window is restored.

566

1

522

501

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments