manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 133 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 133

Instructions for Use Fabius MRI SW 3.n

133

Configuration

Sleep Mode

If 2.5 minutes elapse in Standby mode with no user 
input, Sleep mode is activated. The monitor screen 
is replaced by the screen saver. The screen saver 
displays a message that provides instructions on 
how to activate Standby mode.

Run System Test
1

Press the »

Run System Test

« key. This test 

performs the power-up diagnostic tests (as 
described in “Power-Up Standby Screen” on 
page 86). Pressing this key restores the site 
defaults.

The test results are posted on the screen. Following 
successful completion, the system returns to the 
Standby screen.
This System Test checks the functionality of the 
electronics of the system.

NOTE

If the flow control valves were not shut off before 
entering Standby mode, a »

Gas still flowing

« 

message appears on the Standby screen. The 
message will disappear once the flow is turned off.

523

524

561

516

1

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments