Dräger Fabius Instructions For Use Manual Download Page 40 | Manualshive

Page: 40 / 232

Dräger Fabius Instructions For Use Manual Download Page 40

40

Instructions for Use Fabius MRI SW 3.n

Operation Concept

Rotary Knob

1

The rotary knob is the main control used to
select and confirm all monitoring and system
settings.

–

Turn

the rotary knob to change or select a value

or parameter (clockwise rotation increases a
value; counterclockwise rotation decreases a
value). This function is indicated in the exam-
ples and instructions in this manual by “select.”

–

Press

the rotary knob to set a value or confirm

a selection. If the selection is not confirmed, the
value or parameter will not change. This func-
tion is indicated in the examples and instruc-
tions in this manual by “confirm.”

Fixed Function Keys

The fixed function keys positioned on both sides of
the screen provide access to major machine and
monitoring functions. Most fixed function keys must
be confirmed by pressing the rotary knob.

2

The »

ManSpont

« key selects the Man-

ual/Spontaneous ventilation mode.

3

The »

SIMV/PS

« key is used to select the

SIMV/PS ventilation mode (optional).

4

The »

Pressure Support

« key is used to select

the Pressure Support ventilation mode
(optional).

5

The »

Pressure Control

« key is used to select

the Pressure Control ventilation mode.

6

The »

Volume Control

« key is used to select

the Volume Control ventilation mode.

7

The »

Alarms

« key displays the Alarm Limits

window.

8

The »

Setup

« key provides two different func-

tions, depending on mode:

– If pressed during Standby mode, it displays the

Standby Setup screen which enables the user
to define site defaults and configure system set-
tings (see page 132).

– If pressed during a ventilation mode, it allows

the user to view and change monitoring settings

9

The »

Home

« key displays the main screen from

any other screen currently displayed

10

The »

Silence

« key silences all active alarm

tones for two minutes.

11

The »

Standby

« key switches the machine to

standby mode. Monitoring and alarms are
turned off and the ventilator stops. Fresh gas
monitoring continues.

566

1

11

10

2

3

4

5

6

7

8

9

«
...
38
39
40
41
42
...
»

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments