manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 181 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 181

Instructions for Use Fabius MRI SW 3.n

181

Cleaning

Reinstalling the Scavenger System

Reconnecting the Anesthetic Gas Receiving 
System (AGS)

Every Anesthetic Gas Scavenging System (AGSS) 
used on the Fabius MRI must follow ISO standard 
8835-3.
The scavenging system is used with vacuum 
waste-gas disposal systems.
The AGS or passive scavenger is not applied as an 
independent system.
It is used as one of the three components of the 
AGSS.

z

Hook receiving system with the slots over the 
appropriate pins of the basic device and allow it 
to slide down into place.

1

Connect the scavenging hose to the relevant 
socket of the receiving system.

z

Connect the connector of the scavenging hose 
to the terminal unit of the disposal system.

2

Close the connection that is not used with a 
screw cap.

z

Push the transfer hose on the designated 
socket.

z

Connect the other end of the transfer hose to 
the waste-gas port located on the underside of 
the breathing system.

WARNING
Risk of patient injury
If the side openings of the receiving system 
are blocked, negative pressure may result in 
the breathing system and the patient’s lungs.
Always make sure the side openings of the 
receiving system are not blocked.

NOTE

Remove the socket from the scavenger hose 
before connecting.

NOTE

The scavenger hoses must not be pinched, 
kinked, or blocked in any manner.

061

2

1

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments