Dräger Fabius Instructions For Use Manual Download Page 171

Page: 171 / 232

Instructions for Use Fabius MRI SW 3.n

171

Cleaning

Removing the Compact Breathing Sys-
tem

Remove all breathing hoses.

Disconnect the breathing bag extension and
bag by loosening the two thumb screws.

Remove the ventilation hose.

Remove the fresh gas hose from the breathing
system.

Remove the scavenger hose.

Remove the flow sensor cable.

Remove the O

sensor cable.

Remove the breathing pressure cable.

Detach the APL-bypass and the PEEP/P

MAX

lines from the breathing system and from the
side of the machine.

Remove the absorber (for complete instruc-
tions, see page 189

Remove the compact breathing system.

Remove plug for the inspiration dome.

Removing the Inspiratory Valve
2

Unscrew the retaining nut.

Remove the inspection cap.

Extract the valve disc.

Extract the gasket on top of the valve disc.

Removing the Expiratory Valve
6

Unscrew the retaining nut.

Remove the inspection cap.

Extract the valve disc.

Remove the gasket on top of the valve disc.

060

Summary of Contents for Fabius









































































































































































































































Search results

Summary of Contents for Fabius

Reviews:

Dräger Fabius, Instructions For Use Manual, Page: 171 / 232

Search results

Summary of Contents for Fabius

Reviews: