manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 103 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 103

Instructions for Use Fabius MRI SW 3.n

103

Operation

Starting Pressure Support Ventilation

The following examples and illustrations describe 
starting Pressure Support ventilation from the 
present ventilation mode “Volume Control”:

1

Press the »

Pressure Support

« key. The LED 

associated with this key starts blinking. It 
remains blinking until the selected mode of 
operation is confirmed.

2

The Waveform window is replaced by the venti-
lator settings window and a message that pro-
vides instructions to confirm the mode change.

z

If the ventilator settings are correct, confirm the 
mode change.

z

If the ventilator settings are not correct, for each 
parameter that needs to change, press the cor-
responding soft key, select the correct value, 
and confirm the change. When the parameter 
changes are completed, confirm the ventilation 
mode change.

z

After the mode change is confirmed, the 
»

Pressure Support

« key LED switches from 

blinking to constantly on, the ventilator switches 
to the Pressure Support mode, and the wave-
form is restored.

564

2

1

52

1

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments