manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 47 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 47

Instructions for Use Fabius MRI SW 3.n

47

Operation Concept

Fresh Gas Flow Monitoring Resolution

The Fabius MRI can be configured by 
DrägerService or your local authorized service 
organization to display fresh gas flow rates either in 
a standard resolution mode or in a high resolution 
mode:

1

If 

standard resolution

 is configured, the elec-

tronic fresh gas flow indicators support 
100 mL/min increments (format xx.x L/min), and 
the flow meters on the monitor screen indicate 
a range of 0 to 12 L/min.

2

If 

high resolution

 is configured, the electronic 

fresh gas flow indicators support 10 mL/min 
increments (format x.xx L/min), and the flow 
meters on the monitor screen indicate a range 
of 0 to 10 L/min with an emphasis on resolution 
at the lower end of the scale.
High-resolution data is displayed when all indi-
vidual gas flows are below 9.99 L/min.
Switching to standard resolution occurs when 
the highest flow rate is greater than 9.99 L/min.
Switching to high resolution occurs when the 
highest flow rate drops below 9.00 L/min.

501

1

51

1

2

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments