manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 139 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 139

Instructions for Use Fabius MRI SW 3.n

139

Configuration

Access Alarm Log
1

Press the »

Access Alarm Log

« key on the 

Standby screen. The Standby soft key window 
is replaced by the alarm log, which lists all 
alarms with their dates and times.

z

To scroll through the alarm log, turn the rotary 
knob.

z

To delete all alarms from the log, select and 
confirm the »

Clear Alarm Log

« label.

z

To exit the alarm log and return to the Standby 
screen, select and confirm the return arrow.

Restore Site Defaults
2

Press the »

Restore Site Defaults

« key on the 

Standby screen. The predefined site defaults 
are restored, and a »

Site Default settings 

restored

« message is displayed above the 

Standby soft keys.

The site default settings are password protected. 
Changes of the settings can be made via the 
Standby Setup screen, see page 140.

CAUTION

Alarm log data is deleted if Fabius MRI is swit-
ched off or a total loss of electrical power supply 
occurs.

WARNING
Risk of inappropriate ventilation settings
After site default settings have been restored 
check whether the ventilation and monitoring 
settings are appropriate to the patient.

56

1

53

4

561

535

1

2

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments