manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 119 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 119

Instructions for Use Fabius MRI SW 3.n

119

Monitoring

Sorting of displayed alarms

The alarms are sorted according to these catego-
ries. In the categories, the alarms are sorted and 
displayed according to the internal priority system. 
Priority 31 means the highest and priority 1 the low-
est priority. The priority numbers are shown in the 
table "Fault-Cause-Remedy" on page 144.

A maximum of four alarms can be displayed in a list 
at the same time. High-priority alarms are displayed
before low-priority alarms. Low-priority alarms are 
sometimes only displayed after the cause for a 
high-priority alarm has been remedied.

Example of audible alarm notification in the 
event of several alarms.

If an alarm with the category Warning is currently 
active and a new alarm with the category Warning 
is generated, the alarm sequence starts again by 
issuing an alarm with the same priority.

If alarm with the category Caution is also gener-
ated, no new audible alarm is issued. The Warning 
alarm notification is not interrupted because it has 
a higher priority.

If an alarm with the category Caution is currently 
active and a new alarm with the category Caution is
generated, the alarm sequence starts again by 
issuing an alarm with the same priority.

If an alarm with the category Caution is active and 
an alarm with the category Warning is generated, 
the alarm sequence is started for the warning 
because the warning is assigned the highest prior-
ity.

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments