manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 63 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 63

Instructions for Use Fabius MRI SW 3.n

63

Assembly

Connecting the Passive Scavenger*

The passive scavenger system is used only with 
non-recirculating exhaust systems. It is not meant 
to be used with vacuum disposal systems.

z

Install the passive scavenger on the machine by 
sliding its bracket onto the two shoulder screws 
located on the scavenger mounting bracket on 
the side of the machine.

1

Connect one end of the transfer hose to the side 
fitting on the scavenger.

z

Connect the other end of the transfer hose to 
the waste gas port located on the underside of 
the breathing system.

2

Connect the waste gas hose to the bottom con-
nection on the scavenger.

z

Connect the other end of the hose to the hospi-
tal waste gas disposal system.

For detailed information on the passive scavenger 
system, refer to separate Instructions for Use.

*

optional

NOTE

The scavenger hoses must not be pinched, 
kinked, or blocked in any manner.

NOTE

Remove the socket from the scavenger hose 
before connecting.

062

1

2

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments