manualshive.com logo in svg

Dräger Fabius, Instructions For Use Manual, Page: 8 / 232

Share
Download
Dräger Fabius Instructions For Use Manual Download Page 8

8

Instructions for Use Fabius MRI SW 3.n

For Your Safety and that of Your Patients

Strictly follow these Instructions for Use

Maintenance

Accessories

Not for use in areas of explosion hazard

Safe connection with other electrical equipment

Safe networking of computers

When networking with electrical devices, the oper-
ator is responsible for ensuring that the resulting 
system meets the requirements set forth by the fol-
lowing standards:
– EN 60601-1 (IEC 60601-1)

Medical electrical equipment 
Part 1: General requirements for safety

– EN 60601-1-1 (IEC 60601-1-1)

Medical electrical equipment 
Part 1-1: General requirements for safety
Collateral standard: Safety requirements for 
medical electrical systems

– EN 60601-1-2 (IEC 60601-1-2)

Medical electrical equipment 
Part 1-2: General requirements for safety
Collateral standard: Electromagnetic compati-
bility; Requirements and tests

– EN 60601-1-4 (IEC 60601-1-4)

Medical electrical equipment 
Part 1-4: General requirements for safety
Collateral standard: Programmable electrical 
medical systems

Follow associated Assembly Instructions and 
Instructions for Use.

WARNING
Strictly follow these Instructions for Use. Any 
use of the medical device requires full under-
standing and strict observation of all portions 
of these instructions. The medical device is 
only to be used for the purpose specified 
under “Intended Use” on page 16 and in con-
junction with appropriate patient monitoring 
(see page 9). Strictly observe all WARNING 
and CAUTION statements throughout this 
Instruction for Use and all statements on 
medical device labels.

WARNING
The medical device must be inspected and 
serviced regularly by trained service person-
nel.
Repair of the medical device may also only be 
carried out by trained service personnel. 
Dräger recommends that a service contract be 
obtained with DrägerService and that all 
repairs also be carried out by them. Dräger 
recommends that only authentic Dräger repair 
parts be used for maintenance. Otherwise the 
correct functioning of the medical device may 
be compromised.
See chapter "Maintenance".

WARNING
Only the accessories indicated on the list of 
accessories 9052102 enUS (1st edition or hig-
her) have been tested and approved to be 
used with the medical device. Accordingly it is 
strongly recommended that only these acces-
sories be used in conjunction with the specific 
medical device. Otherwise the correct func-
tioning of the medical device may be compro-
mised.

WARNING
This medical device is neither approved nor 
certified for use in areas where combustible or 
explosive gas mixtures are likely to occur.

WARNING
Electrical connections to equipment which is 
not listed in these Instructions for Use should 
only be made following consultation with the 
respective manufacturers.

Summary of Contents for Fabius









































































































































































































































Reviews:

No comments