Dräger Fabius Instructions For Use Manual Download Page 134

Page: 134 / 232

Configuration

134

Instructions for Use Fabius MRI SW 3.n

Calibrate Flow Sensor

Press the »

Calibrate Flow Sensor

« key on the

Standby screen. The Standby soft key window
is replaced by instructions for performing the
calibration.

Follow the instructions on the screen:

– Close all fresh gas control valves.
– Remove expiratory hose from breathing sys-

tem.

– To start Flow Sensor Calibration, press rotary

knob.

When the calibration begins, the instructions
are removed, and a »

Flow Calibration in

progress

« message is displayed above the

Standby soft keys.

When the calibration is completed, one of two
messages is posted above the Standby soft
keys: »

Flow Calibration completed - recon-

nect expiratory hose

« or »

Flow Calibration

Failed

«.

Troubleshooting Flow Calibration Failure

If the flow sensor cannot be calibrated, retry the cal-
ibration.
If the flow sensor still cannot be calibrated, call
DrägerService or your local authorized service
organization.

599

526

527

Summary of Contents for Fabius









































































































































































































































Search results

Summary of Contents for Fabius

Reviews:

Dräger Fabius, Instructions For Use Manual, Page: 134 / 232

Search results

Summary of Contents for Fabius

Reviews: