Canon imageRUNNER ADVANCE C3330 Series, Service Manual

Page: 556 / 1225

197-1081-05 Serial communication error
Detection Description A communication error between the CPU of the DC Controller PCB and KONA1 (ASIC) in the DC
Controller PCB was detected. (An error caused by software)
Remedy
[Remedy] Turn OFF and then ON the main power.
[Reference] Data (device information) is reset by turning OFF and then ON the main power.
197-1082-05 Serial communication error
Detection Description A communication error between the CPU of the DC Controller PCB and KONA2 (ASIC) in the DC
Controller PCB was detected. (An error caused by software)
Remedy [Remedy] Turn OFF and then ON the main power.
[Reference] Data (device information) is reset by turning OFF and then ON the main power.
197-1084-05 Serial communication error
Detection Description A communication error between the DC Controller PCB and the Laser Driver PCB was detected.
(An error caused by software)
Remedy [Remedy] Turn OFF and then ON the main power.
[Reference] Data (device information) is reset by turning OFF and then ON the main power.
197-5000-05 Serial communication error
Detection Description A communication error between the DC Controller PCB and the Secondary Transfer High Voltage
PCB was detected at power-on.
Remedy [Related parts]
- Harness between the DC Controller PCB (UN04/J112 and J114) and the Secondary Transfer
High Voltage PCB (UN03/J502 and J501) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB)
- Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRANSFER H.V. PCB
ASSEMBLY)
- DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2
min) and restore the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
197-5001-05 Serial communication error
Detection Description A communication error between the DC Controller PCB and the Primary Transfer High Voltage
PCB was detected at power-on.
Remedy [Related parts]
- Harness between the DC Controller PCB (UN04/J113) and the Primary Transfer High Voltage
PCB (UN02/J401) (Unit of replacement: CABLE, PRIMARY TRANSFER H.V.)
- Primary Transfer High Voltage PCB (UN02) (Unit of replacement: 1ST TRNSFR. H.V. PCB
ASS'Y)
- DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2
min) and restore the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
199-0101-05 Error in high voltage sequence (Y)
Detection Description Error for collecting log.
Remedy [Remedy] Collect debug log and contact to the sales company.
[Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled
as an error.
199-0102-05 Error in high voltage sequence (M)
Detection Description Error for collecting log.
Remedy [Remedy] Collect debug log and contact to the sales company.
[Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled
as an error.
7. Error/Jam/Alarm
544