manualshive.com logo in svg

NXP Semiconductors LPC43Sxx, Руководство пользователя

Поделиться
Скачать
NXP Semiconductors LPC43Sxx Скачать руководство пользователя страница 662

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2015. All rights reserved.

User manual

Rev. 2.1 — 10 December 2015 

662 of 1441

NXP Semiconductors

UM10503

Chapter 25: LPC43xx/LPC43Sxx USB0 Host/Device/OTG controller

 

25.6.7.2 Host mode

This 32-bit register contains the beginning address of the Periodic Frame List in the 
system memory. The host controller driver (HCD) loads this register prior to starting the 
schedule execution by the Host Controller. The memory structure referenced by this 
physical memory pointer is assumed to be 4 kB aligned. The contents of this register are 
combined with the Frame Index Register (FRINDEX) to enable the Host Controller to step 
through the Periodic Frame List in sequence.

 

25.6.8 Endpoint List Address register (ENDPOINTLISTADDR - device) and 

Asynchronous List Address (ASYNCLISTADDR - host) registers 

25.6.8.1 Device mode

In device mode, this register contains the address of the top of the endpoint list in system 
memory. Bits[10:0] of this register cannot be modified by the system software and will 
always return a zero when read. The memory structure referenced by this physical 
memory pointer is assumed 64 byte aligned. The entire device endpoint list must be 
aligned on a 2 kB boundary.

Table 479. USB Device Address register in device mode (DEVICEADDR - address 0x4000 6154) bit description

Bit

Symbol

Value Description

Reset 
value

Access

23:0

-

Reserved

0

-

24

USBADRA

Device address advance 

0

Any write to USBADR are instantaneous.

1

When the user writes a one to this bit at the same time or before USBADR 
is written, the write to USBADR fields is staged and held in a hidden 
register. After an IN occurs on endpoint 0 and is acknowledged, USBADR 
will be loaded from the holding register.

Hardware will automatically clear this bit on the following conditions:

•

IN is ACKed to endpoint 0. USBADR is updated from the staging 
register.

•

OUT/SETUP occurs on endpoint 0. USBADR is 

not

 updated.

•

Device reset occurs. USBADR is set to 0.

Remark: 

After the status phase of the SET_ADDRESS descriptor, the 

DCD has 2 ms to program the USBADR field. This mechanism will ensure 
this specification is met when the DCD can not write the device address 
within 2 ms from the SET_ADDRESS status phase. If the DCD writes the 
USBADR with USBADRA=1 after the SET_ADDRESS data phase (before 
the prime of the status phase), the USBADR will be programmed instantly 
at the correct time and meet the 2 ms USB requirement.

31:25

USBADR

USB device address

0

R/W

Table 480. USB Periodic List Base register in host mode (PERIODICLISTBASE - address 0x4000 6154) bit 

description 

Bit

Symbol

Description

Reset 
value

Access

11:0

-

Reserved

-

-

31:12

PERBASE31_12

Base Address (Low)

These bits correspond to the memory address signals 31:12.

-

R/W

Содержание LPC43Sxx


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды