NXP Semiconductors LPC43Sxx Скачать руководство пользователя страница 324

Страница: 324 / 1441

UM10503

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 2.1 — 10 December 2015

324 of 1441

NXP Semiconductors

UM10503

Chapter 16: LPC43xx/LPC43Sxx Pin configuration

P8_6

[2]

I; PU I/O

GPIO4[6] —

General purpose digital input/output pin.

USB1_ULPI_NXT —

ULPI link NXT signal. Data flow control signal from the

PHY.

R —

Function reserved.

LCD_VD5 —

LCD data.

LCD_LP —

Line synchronization pulse (STN). Horizontal synchronization

pulse (TFT).

R —

Function reserved.

R —

Function reserved.

T0_CAP2 —

Capture input 2 of timer 0.

P8_7

[2]

I; PU I/O

GPIO4[7] —

General purpose digital input/output pin.

USB1_ULPI_STP —

ULPI link STP signal. Asserted to end or interrupt

transfers to the PHY.

R —

Function reserved.

LCD_VD4 —

LCD data.

LCD_PWR —

LCD panel power enable.

R —

Function reserved.

R —

Function reserved.

T0_CAP3 —

Capture input 3 of timer 0.

P8_8

[2]

I; PU -

R —

Function reserved.

USB1_ULPI_CLK —

ULPI link CLK signal. 60 MHz clock generated by the

PHY.

R —

Function reserved.

R —

Function reserved.

R —

Function reserved.

R —

Function reserved.

CGU_OUT0 —

CGU spare clock output 0.

I2S1_TX_MCLK —

I2S1 transmit master clock.

P9_0

[2]

I; PU I/O

GPIO4[12] —

General purpose digital input/output pin.

MCABORT —

Motor control PWM, LOW-active fast abort.

R —

Function reserved.

R —

Function reserved.

R —

Function reserved.

ENET_CRS —

Ethernet Carrier Sense (MII interface).

I/O

SGPIO0 —

General purpose digital input/output pin.

I/O

SSP0_SSEL —

Slave Select for SSP0.

Table 186. LPC4370/LPC43S70 Pin description

…continued

LCD is not available on all parts.

Symbol

GA25

TFBGA100

t st

ate

]

Description

Содержание LPC43Sxx


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание LPC43Sxx

Отзывы:

Бренды по названию

Популярные бренды

NXP Semiconductors LPC43Sxx, Руководство пользователя

Результаты поиска

Содержание LPC43Sxx

Отзывы:

Бренды по названию

Популярные бренды