manualshive.com logo in svg

NXP Semiconductors LPC43Sxx, Руководство пользователя

Поделиться
Скачать
NXP Semiconductors LPC43Sxx Скачать руководство пользователя страница 562

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2015. All rights reserved.

User manual

Rev. 2.1 — 10 December 2015 

562 of 1441

NXP Semiconductors

UM10503

Chapter 22: LPC43xx/LPC43Sxx SD/MMC interface

22.6.27 Bus Mode Register

 

22.6.28 Poll Demand Register 

 

Table 384. Bus Mode Register (BMOD, address 0x4000 4080) bit description

Bit

Symbol

Value

Description

Reset 
value

0

SWR

Software Reset. When set, the DMA Controller resets all its internal registers. SWR 
is read/write. It is automatically cleared after 1 clock cycle.

0

1

FB

Fixed Burst. Controls whether the AHB Master interface performs fixed burst 
transfers or not. When set, the AHB will use only SINGLE, INCR4, INCR8 or 
INCR16 during start of normal burst transfers. When reset, the AHB will use 
SINGLE and INCR burst transfer operations. FB is read/write.

0

6:2

DSL

Descriptor Skip Length. Specifies the number of HWord/Word/Dword to skip 
between two unchained descriptors. This is applicable only for dual buffer 
structure. DSL is read/write.

0

7

DE

SD/MMC DMA Enable. When set, the SD/MMC DMA is enabled. DE is read/write.

10:8

PBL

Programmable Burst Length. These bits indicate the maximum number of beats to 
be performed in one SD/MMC DMA transaction. The SD/MMC DMA will always 
attempt to burst as specified in PBL each time it starts a Burst transfer on the host 
bus. The permissible values are 1, 4, 8, 16, 32, 64, 128 and 256. This value is the 
mirror of MSIZE of FIFOTH register. In order to change this value, write the 
required value to FIFOTH register. This is an encode value as follows.Transfer unit 
is 32 bit. PBL is a read-only value.

0

0x0

1 transfer

0x1

4 transfers

0x2

8 transfers

0x3

16 transfers

0x4

32 transfers

0x5

64 transfers

0x6

128 transfers

0x7

256 transfers

31:11

-

Reserved

Table 385. Poll Demand Register (PLDMND, address 0x4000 4084) bit description

Bit

Symbol

Description

Reset 
value

31:0

PD

Poll Demand. If the OWN bit of a descriptor is not set, the FSM 
goes to the Suspend state. The host needs to write any value 
into this register for the SD/MMC DMA state machine to resume 
normal descriptor fetch operation. This is a write only register. 
PD bit is write-only.

Содержание LPC43Sxx


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды