manualshive.com logo in svg

NXP Semiconductors LPC43Sxx, Руководство пользователя

Поделиться
Скачать
NXP Semiconductors LPC43Sxx Скачать руководство пользователя страница 546

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2015. All rights reserved.

User manual

Rev. 2.1 — 10 December 2015 

546 of 1441

NXP Semiconductors

UM10503

Chapter 22: LPC43xx/LPC43Sxx SD/MMC interface

2

DMA_RESET

Dma reset. To reset DMA interface, software should set bit to 1. This 
bit is auto-cleared after two AHB clocks.

0

0

No change.

1

Reset. Reset internal DMA interface control logic

3

-

Reserved

-

4

INT_ENABLE

Global interrupt enable/disable bit. The int port is 1 only when this bit 
is 1 and one or more unmasked interrupts are set.

0

0

Disable interrupts

1

Enable interrupts

5

-

Reserved. Always write this bit as 0.

0

6

READ_WAIT

Read/wait. For sending read-wait to SDIO cards.

0

0

Clear read wait

1

Assert read wait

7

SEND_IRQ_RESPONSE

Send irq response. This bit automatically clears once response is 
sent. To wait for MMC card interrupts, the host issues CMD40, and 
the SD/MMC controller waits for an interrupt response from the MMC 
card. In the meantime, if the host wants the SD/MMC interface to exit 
waiting for interrupt state, it can set this bit, at which time the 
SD/MMC interface command state-machine sends a CMD40 
response on the bus and returns to idle state.

0

0

No change

1

Send auto IRQ response

8

ABORT_READ_DATA

Abort read data. Used in SDIO card suspend sequence.

0

0

No change

1

Abort. After suspend command is issued during read-transfer, 
software polls card to find when suspend happened. Once suspend 
occurs, software sets bit to reset data state-machine, which is waiting 
for next block of data. This bit automatically clears once data state 
machine resets to idle.
Used in SDIO card suspend sequence.

9

SEND_CCSD

Send ccsd. When set, the SD/MMC controller sends CCSD to the 
CE-ATA device. Software sets this bit only if current command is 
expecting CCS (that is, RW_BLK) and interrupts are enabled in 
CE-ATA device. Once the CCSD pattern is sent to device, the 
SD/MMC interface automatically clears send_ccsd bit. It also sets 
Command Done (CD) bit in RINTSTS register and generates interrupt 
to host if Command Done interrupt is not masked. 
NOTE: Once send_ccsd bit is set, it takes two card clock cycles to 
drive the CCSD on the CMD line. Due to this, during the boundary 
conditions it may happen that CCSD is sent to the CE-ATA device, 
even if the device signalled CCS.

0

0

Clear bit if the SD/MMC controller does not reset the bit.

1

Send Command Completion Signal Disable (CCSD) to CE-ATA 
device

Table 358. Control Register (CTRL, address 0x4000 4000) bit description

Bit

Symbol

Value

Description

Reset 
value

Содержание LPC43Sxx


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды