manualshive.com logo in svg

NXP Semiconductors LPC43Sxx, Руководство пользователя

Поделиться
Скачать
NXP Semiconductors LPC43Sxx Скачать руководство пользователя страница 1332

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2015. All rights reserved.

User manual

Rev. 2.1 — 10 December 2015 

1332 of 1441

NXP Semiconductors

UM10503

Chapter 47: LPC43xx/LPC43Sxx 10-bit ADC0/1

47.6.3 A/D Interrupt Enable register 

This register allows control over which A/D channels generate an interrupt when a 
conversion is complete. For example, it may be desirable to use some A/D channels to 
monitor sensors by continuously performing conversions on them. The most recent 
results are read by the application program whenever they are needed. In this case, an 
interrupt is not desirable at the end of each conversion for some A/D channels.

 

47.6.4 A/D Data Registers 

The A/D Data Register hold the result when an A/D conversion is complete, and also 
include the flags that indicate when a conversion has been completed and when a 
conversion overrun has occurred.

 

29:27 -

Reserved. These bits always read as zeroes. 

0

30

OVERRUN

This bit is 1 in burst mode if the results of one or more conversions 
was (were) lost and overwritten before the conversion that 
produced the result in the V_VREF bits.

0

31

DONE

This bit is set to 1 when an analog-to-digital conversion completes. 
It is cleared when this register is read and when the AD0/1CR 
register is written. If the AD0/1CR is written while a conversion is 
still in progress, this bit is set and a new conversion is started.

0

Table 1115. A/D Global Data register (GDR - address 0x400E 3004 (ADC0) and 0x400E 4004 

(ADC1)) bit description

Bit

Symbol

Description

Reset 
value

Table 1116. A/D Interrupt Enable register (INTEN - address 0x400E 300C (ADC0) and 

0x400E 400C (ADC1)) bit description

Bit

Symbol

Description

Reset 
value

7:0

ADINTEN 

These bits allow control over which A/D channels generate 
interrupts for conversion completion. When bit 0 is one, completion 
of a conversion on A/D channel 0 will generate an interrupt, when bit 
1 is one, completion of a conversion on A/D channel 1 will generate 
an interrupt, etc.

0x00

8

ADGINTEN

When 1, enables the global DONE flag in ADDR to generate an 
interrupt. When 0, only the individual A/D channels enabled by 
ADINTEN 7:0 will generate interrupts.

1

31:9 -

Reserved. Always 0.

0

Table 1117. A/D Data registers (DR - addresses 0x400E 3010 (DR0) to 0x400E 302C (DR7) 

(ADC0); 0x400E 4010 (DR0) to 0x400E 402C (DR7) (ADC1)) bit description

Bit

Symbol

Description

Reset 
value

5:0

-

Reserved. Always 0.

0

15:6

V_VREF

When DONE is 1, this field contains a binary fraction representing the 
voltage on the ADCn input pin selected in 

Table 1114

, divided by the 

voltage on the VDDA pin. Zero in the field indicates that the voltage on 
the ADCn input pin was less than, equal to, or close to that on VDDA, 
while 0x3FF indicates that the voltage on ADCn input pin was close to, 
equal to, or greater than that on VDDA.

-

Содержание LPC43Sxx


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды