![background image](http://html.mh-extra.com/html/mitsubishi-electric/melsec-l-series/melsec-l-series_user-manual_2387571031.webp)
Appendix - 83
Appendices
(5) Servo parameter
(a) Control of servo parameters
Parameters of IAI electric actuator controller are not controlled by the
Simple Motion module. Therefore, even though the parameter of IAI
electric actuator controller is changed during the communication
between the Simple Motion module and IAI electric actuator controller,
the change is not applied to the buffer memory of the Simple Motion
module..
(6) Optional data monitor
Optional data monitor is not available.
(7) Gain switching command, PI-PID switching request, Semi/Fully closed loop
switching request
Gain switching command, PI-PID switching request, and Semi/Fully closed
loop switching request
are not available.
(8) Driver communication
The driver communication is not supported.
If the driver communication is set in a servo parameter,
the setting is
ignored.
(9) Torque limit
The torque limit set by the Simple Motion module is ignored. Set the torque
limit value with the parameter on the IAI electric actuator controller side.
(10) Axis monitor data
(a) "
Md.104
Motor current value
" is always "0". When the optional data
monitor is not used, "
Md.109
Regenerative load ratio/Optional data monitor
output 1
", "
Md.110
Effective load torque/Optional data monitor output 2
", and
"
Md.111
Peak torque ratio/Optional data monitor output 3
" are "0".
(b) "Zero point pass" (
Md.108
Servo status
(low-order buffer memory
address): b0) is always OFF.
(c) "Zero speed" (
Md.108
Servo status
(low-order buffer memory address):
b3) and "Speed limit" (
Md.108
Servo status
(low-order buffer memory
address): b4) are always OFF.
(d) "
Md.113
Semi/Fully closed loop status
" is always "0".
(e) "
Md.107
Parameter error No.
" is always "0".
(f) "In-position" (
Md.108
Servo status
(high-order buffer memory address):
b12) is OFF during the axis operation. It is turned ON when the axis
operation is completed.
(11) Amplifier-less operation
The amplifier-less operation cannot be used to the IAI electric actuator
controller axis. If the amplifier-less operation is used, the IAI electric
actuator controller set axis is not connected.
Содержание MELSEC-L Series
