MUTOH ValueJet VJ-1324, Maintenance Manual, Page: 336 / 439

5.7.8 Top&Bottom adjustment Menu P.5-50
5.7 Adjustment Menu VJ1324E-M-02
5.7.8 Top&Bottom adjustment Menu
After printing and cutting the media, enter the distances of between Front sensor and Head (Top
margin), Cutter and Head (Bottom margin), and Media edge sensor and Head (print start location), and
adjust Top, Bottom, and Side margins.
Follow the procedure below to adjust.
1.
Set media as necessary.
2. After media is set, the detected width of the set media is displayed.
3. After media is set, the printer prints out band feed correction adjustment patterns in the following
modes.
• Black, 1 pass, Uni-D, 360 dpi
• If "check" is selected, black replaces magenta.
4. Check the printed top & bottom adjustment patterns for the measurement.
Measue each margins with a scale and so on.
5.
Enter each measured value as the parameter.
6. Perform "Print: Check", print out the Top&Bottom adjustment pattern, and cut the media.
7. Measure the followings on the print result and check that the print margins are adjusted.
１ ：
Top margin
２ ： Bottom margin
３ ：
Side margin
8. If the margins are not adjusted, repeat (3) to (7).
Bottom margin
Top margin
media feeding direction
side margin
= ?ࠠ࡯
= ?MG[
=?MG[
[Enter]
[Enter]
㧭㨐㨖㨡㨟㨠㨙㨑㨚㨠ޓ㧼㨞㨕㨚㨠
㧭㨐㨖㧚㧥㧦㨀㨛㨜㧒㧮㨛㨠㨠㨛㨙
㧯㨔㨑㨏㨗ޓ㧠㧦㧭㨐㨖㨡㨟㨠㨙㨑㨚㨠
㨀㨛㨜㧹㨍㨞㨓㨕㨚㧦ޓޓޓޓ㧠㧜㧚㧜㨙㨙
㧮㨛㨠㨠㨛㨙㧹㨍㨞㨓㨕㨚㧦ޓޓ㧡㧚㧜㨙㨙
㧿㨕㨐㨑㧹㨍㨞㨓㨕㨚㧦ޓޓޓޓ㧡㧚㧜㨙㨙
[Enter]
㧹㨑㨐㨕㨍㨃㨕㨐㨠㨔㧦㧝㧜㧜㧜㨙㨙
㧼㨞㨕㨚㨠㧦㧵㨚㨕㨠㨕㨍㨘
[Enter]
䌓䌥䌬䌥䌣䌴䇭䌉䌮䌩䌴䌩䌡䌬䇭 or Check by 䇸 + 䇹 / 䇸 - 䇹䌫䌥䌹 .
Use the [ 㫧 ] key by 0.1mm to set
䌔䌯䌰䇭䌭䌡䌲䌧䌩䌮䇭 35.0 䌾 45.0 䌭䌭
䌂䌯䌴䌴䌯䌭䇭䌭䌡䌲䌧䌩䌮䇭
0.0
䌾
10.0
䌭䌭
䌓䌩䌤䌥䇭䌭䌡䌲䌧䌩䌮䇭 0.0 䌾 10.0 䌭䌭
Press down [Enter]
at "SideMargin" to
save the input value.
㨃㨍㨕㨠ޓ㨒㨛㨞ޓ㨍ޓ㨣㨔㨕㨘㨑
㨃㨍㨕㨠ޓ㨒㨛㨞ޓ㨍ޓ㨣㨔㨕㨘㨑