Mazda CX-9 Grand Touring 2007 Manual Download Page 474

Page: 474 / 1056

DTC P0203 [MZI-3.5]

DTC P0203 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

Inspect the fuel injector No.2.

(see

FUEL INJECTOR

INSPECTION [MZI-3.5]

Is there any malfunction?

Go to the next step.

VERIFY TROUBLESHOOTING OF
DTC P0202 HAS BEEN COMPLETED

Verify that all disconnected

connectors reconnected.

Clear DTC from memory using M-
MDS.

Start the engine.

Perform the "KOEO/KOER self-
test"

(See

KOEO/KOER SELF TEST

[MZI-3.5]

Is same DTC present?

Yes

Replace the PCM, then go to the next
step.

Go to the next step.

VERIFY AFTER REPAIR

PROCEDURE

Perform the "AFTER REPAIR
PROCEDURE".

(See

AFTER REPAIR

PROCEDURE [MZI-3.5]

Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See

DTC TABLE [MZI-3.5]

Troubleshooting completed.

DTC P0203

Injector circuit/open-cylinder No.3

DETECTION
CONDITION

The CCM monitors the operation of the fuel injector drivers in the PCM. The test
if the fuel injector circuitry is inoperative.

POSSIBLE CAUSE

Fuel injector No.3 malfunction

Connector or terminal malfunction

Open circuit between fuel pump relay and fuel injector No.3 terminal B

Open circuit between fuel injector No.3 terminal A and PCM terminal 2BF

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:30 AM

Page 127

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands