manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

With advanced keyless entry system: 

z

Between coil terminal A and 

keyless control module terminal 
3V  

z

Between coil terminal B and 

keyless control module terminal 
3U  

 
Without advanced keyless entry 

system: 

z

Between coil terminal A and 
instrument cluster terminal 1G  

z

Between coil terminal B and 

instrument cluster terminal 1E  

 

Is there any malfunction?

No

Go to the next step, (with advanced 
keyless entry system.) 

Go to Step 8. (without advanced keyless 
entry system.)

7

Inspect the following wiring harnesses 
and connectors for an open or short 

circuit: 

z

Between keyless control module 

terminal 3W and instrument 
cluster terminal 1W  

z

Between keyless control module 

terminal 3X and instrument 
cluster terminal 1X  

 

Is there any malfunction?

Yes

Repair or replace wiring harness and 
connectors.

No

Go to the next step.

8

Inspect for the following wiring 

harnesses and connectors: 

z

Between PCM terminal 1BG and 
instrument cluster terminal 1W  

z

Between PCM terminal 1BL and 

instrument cluster terminal 1X  

 

Is there any malfunction?

Yes

Repair or replace the suspected wiring 

harness and connector.

No

Go to the next step.

9

Verify the following: 

Yes

Go to the next step.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:37 AM

Page 24 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Jeep UNIVERSAL CJ-2A Operation Data preview
UNIVERSAL CJ-2A
Brand: Jeep Pages: 27
Jeep RENEGADE 2016 User Manual preview
RENEGADE 2016
Brand: Jeep Pages: 228
Jeep PATRIOT 2013 User Manual preview
PATRIOT 2013
Brand: Jeep Pages: 108
Jeep PATRIOT 2013 Owner'S Manual preview
PATRIOT 2013
Brand: Jeep Pages: 525
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Brand: Kolpin Outdoors Pages: 6
Schartec CR 4 Manual preview
CR 4
Brand: Schartec Pages: 2
STC 552-010 Installation Instructions Manual preview
552-010
Brand: STC Pages: 6
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Brand: Mercedes-Benz Pages: 54
Ecco EC4210B-K Installation And Operation Instructions Manual preview
EC4210B-K
Brand: Ecco Pages: 9
Volvo 164 1969 Service Manual preview
164 1969
Brand: Volvo Pages: 266
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Brand: Oldsmobile Pages: 340
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Brand: Cadillac Pages: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Brand: TIE DOWN Pages: 2
Audi S4 Biturbo Buyer'S Manual preview
S4 Biturbo
Brand: Audi Pages: 9
SkyRack SR-CB-101 Assembly And Instruction Sheet preview
SR-CB-101
Brand: SkyRack Pages: 2
Dacia Duster Driver'S Handbook Manual preview
Duster
Brand: Dacia Pages: 244
BrandMotion AVMS-3604 Installation Instructions Manual preview
AVMS-3604
Brand: BrandMotion Pages: 9

Brands by name

Popular brands

Load more brands