Mazda CX-9 Grand Touring 2007 Manual Download Page 173

Page: 173 / 1056

{

Engine speed (PID: RPM)

{

Rear HO2S voltage (PID: O2S12, O2S22)

3. Drive the vehicle and decelerate the engine speed by releasing the accelerator pedal fully when the engine

speed is

3,000 rpm or more.

4. Verify that the rear HO2S outputs a voltage of

0.6 V or more,

one time or more, then verify that the rear

HO2S voltage (PID: O2S12, O2S22) is

0.3 V is or less

while decelerating as shown in the figure.

Fig. 29: Rear HO2S Outputs Voltage Graph

Courtesy of MAZDA MOTORS CORP.

If not within the specification, inspect the rear HO2S for an open or short circuit. Then if there is no

malfunction in the wiring harness, replace the rear HO2S. (See

REAR HEATED OXYGEN

SENSOR (HO2S) REMOVAL/INSTALLATION [MZI-3.5]

HO2S HEATER RESISTANCE INSPECTION

1. Disconnect the HO2S connector.
2. Measure the resistance between HO2S terminals C and A.

If it is not within the specification, replace the HO2S. (See

REAR HEATED OXYGEN SENSOR

(HO2S) REMOVAL/INSTALLATION [MZI-3.5]

If the monitor item status/specification (reference) is not within the specification, even though the

resistance is within the specification, perform the "Circuit Open/Short Inspection".

HO2S heater resistance

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Control System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:25:31 AM

Page 32

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands