Mazda CX-9 Grand Touring 2007 Manual Download Page 163

Page: 163 / 1056

CKP sensor terminal A and power supply

CKP sensor terminal A and body ground

CKP sensor terminal B and power supply

CKP sensor terminal B and body ground

CAMSHAFT POSITION (CMP) SENSOR REMOVAL/INSTALLATION [MZI-3.5]

1. Disconnect the negative battery cable.
2. Remove the battery.
3. Remove the following part for easier access.

Remove the resonance chamber and air cleaner assy. (see

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.5]

4. Disconnect the CMP sensor connector
5. Remove the CMP sensor.

6. Install in the reverse order of removal.

Fig. 20: View Of CMP Sensor With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

CAMSHAFT POSITION (CMP) SENSOR INSPECTION [MZI-3.5]

NOTE:

Lubricate the CMP O-ring seal with clean engine oil.

NOTE:

Before performing the following inspection, make sure to follow the

procedure as indicated in the troubleshooting flowchart. (see HOW TO
USE THIS MANUAL .)

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Control System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:25:31 AM

Page 22

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands