manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

and/or on-line repair information 
availability.  

z

Is any related Service Bulletins 

available?  

the available Service Bulletins. 

z

If the vehicle is not repaired, go to 

the next step.  

No

Go to the next step.

3

INSPECT MAF SENSOR 
CONNECTOR FOR POOR 

CONNECTION

 

z

Turn the ignition switch off.  

z

Disconnect the MAF/IAT sensor 

connector.  

z

Inspect for poor connection (such 
as damaged/pulled-out pins, 

corrosion).  

z

Are there any malfunction?  

Yes

Repair or replace suspected part, then go to 
Step 10.

No

Go to the next step.

4

INSPECT POWER SUPPLY 

CIRCUIT FOR OPEN CIRCUIT

 

z

Turn the ignition switch to the ON 
position (Engine off).  

z

Measure the voltage between 

MAF sensor terminal A and body 
ground.  

z

Is the voltage B+?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 

Step 10.

5

INSPECT PCM CONNECTOR FOR 
POOR CONNECTION

 

z

Turn the ignition switch off.  

z

Disconnect PCM connector.  

z

Inspect for poor connection (such 

as damaged/pulled-out pins, 
corrosion).  

z

Are there any malfunction?  

Yes

Repair or replace suspected part, then go to 
Step 10.

No

Go to the next step.

6

INSPECT MAF SENSOR SIGNAL 
CIRCUIT FOR OPEN CIRCUIT

 

z

Remove PCM with PCM 

connector connected.  

z

Inspect for continuity between the 
following circuits: 

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 
Step 10.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:29 AM

Page 52 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

LaserTrack Flare Installation Manual preview
Flare
Brand: LaserTrack Pages: 12
Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Brand: Jacob Jensen Pages: 2
Yakima K1005 Instructions Manual preview
K1005
Brand: Yakima Pages: 12
TATA Motors Indigo MANZA QUADRAJET 90 Owner'S Manual & Service Book preview
Indigo MANZA QUADRAJET 90
Brand: TATA Motors Pages: 10
CARRYBOY CB-796IG2-CIGD-R Installation Manual preview
CB-796IG2-CIGD-R
Brand: CARRYBOY Pages: 4
GMC 2012 Terrain Owner'S Manual preview
2012 Terrain
Brand: GMC Pages: 428
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Brand: Enduro Pages: 48
Waeco 8885100124 Operating Manual preview
8885100124
Brand: Waeco Pages: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Brand: VBG Pages: 16
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Brand: ULTIMATE SPEED Pages: 50
Power Acoustik METER 4 Installation preview
METER 4
Brand: Power Acoustik Pages: 4
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Brand: Oldsmobile Pages: 380
Subaru 1999 Legacy Owner'S Manual preview
1999 Legacy
Brand: Subaru Pages: 399
Valueline SVL-CARCAM11 User Manual preview
SVL-CARCAM11
Brand: Valueline Pages: 40
VDO FUEL TANK GAUGE Installation Instructions Manual preview
FUEL TANK GAUGE
Brand: VDO Pages: 10
Westfalia 300025300113 Installation Instructions Manual preview
300025300113
Brand: Westfalia Pages: 97
BMW 1998 318ic Electrical Troubleshooting Manual preview
1998 318ic
Brand: BMW Pages: 386
Ocular IOCAP06C-7 4G User Manual preview
IOCAP06C-7 4G
Brand: Ocular Pages: 7

Brands by name

Popular brands

Load more brands