manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DTC P0132, P0138, P0152, P0158 (MZI-3.5) DIAGNOSTIC PROCEDURE

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 
HAS BEEN RECORDED

 

z

Has FREEZE FRAME DATA 

been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 
repair order, then go to the next step.

2

VERIFY RELATED REPAIR 

INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 
and/or on-line repair information 

availability.  

z

Is any related Service Bulletins 
available?  

Yes

Perform repair or diagnosis according to 

the available Service Bulletins. 

z

If the vehicle is not repaired, go to 
the next step.  

No

Go to the next step.

3

VISUALLY INSPECT HO2S 
WIRING HARNESS

 

z

Turn the ignition switch off.  

z

Disconnect the HO2S connector.  

z

Visually inspect the HO2S wiring 

harness. 

{

Check the connector (both 

halves) for contamination  

{

Make sure the connector 
pins are fully seated  

z

Is a concern present?  

NOTE:

z

Disconnect the HO2S wiring 
harness connector.  

Yes

Repair if necessary. Go to Step 9.

No

Go to the next step.

4

INSPECT WHETHER HO2S 

SIGNAL LEVEL IS TOO HIGH

 

z

Connect the HO2S connector.  

z

Turn the ignition switch to the ON 

position (Engine running).  

z

Access the PCM and monitor the 
HO2S signal PID.  

z

Is the voltage less than 1.1 V?  

Yes

Go to Step 6.

No

Go to the next step.

5

PERFORM THOROUGH WIGGLE 

TEST ON HO2S WIRING HARNESS

 

Yes

Repair if necessary. Go to Step 9.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:30 AM

Page 87 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Yakima SideWinder Installation Instructions And Owner'S Manual preview
SideWinder
Brand: Yakima Pages: 8
Roav R5141 Owner'S Manual preview
R5141
Brand: Roav Pages: 10
BMW 3-series convertible Complete Vehicle Workbook preview
3-series convertible
Brand: BMW Pages: 98
Toyota YARIS LIFTBACK 2009 Quick Reference Manual preview
YARIS LIFTBACK 2009
Brand: Toyota Pages: 13
Westfalia 316 145 Manual preview
316 145
Brand: Westfalia Pages: 71
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Brand: GReddy Pages: 9
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Brand: Acura Pages: 6
Voxx Electronics CA-510a Installation Instructions Manual preview
CA-510a
Brand: Voxx Electronics Pages: 15
Scosche HAQ02 Quick Start Manual preview
HAQ02
Brand: Scosche Pages: 8
K&N Engineering Filtercharger 57-9004 Installation Manual preview
Filtercharger 57-9004
Brand: K&N Engineering Pages: 4
Honda Element 2004 Owner'S Manual preview
Element 2004
Brand: Honda Pages: 219
ACV 381190-37-1 Installation Manual preview
381190-37-1
Brand: ACV Pages: 2
Ford 2002 F-250 Owner'S Manual preview
2002 F-250
Brand: Ford Pages: 264
Painless Performance VORTEC 60211 Installation Instructions Manual preview
VORTEC 60211
Brand: Painless Performance Pages: 16
EUFAB 11439 Assembly preview
11439
Brand: EUFAB Pages: 8
PERODUA Aruz 2019 Quick User Manual preview
Aruz 2019
Brand: PERODUA Pages: 43
Scion 2015 FR-S Quick Reference Manual preview
2015 FR-S
Brand: Scion Pages: 24
Curt Group Retrac 207700 Installation Manual preview
Retrac 207700
Brand: Curt Group Pages: 4

Brands by name

Popular brands

Load more brands