Mazda CX-9 Grand Touring 2007 Manual Download Page 352

Page: 352 / 1056

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.

When using the IDS (laptop PC)

1. Select the "Toolbox" tab.
2. Select "DataLogger".
3. Select "Modules".
4. Select "PCM".

When using the PDS (Pocket PC)

1. Select "Module Tests".
2. Select "PCM".
3. Select "DataLogger".

3. Select the PID from the PID table.
4. Verify the test results according to detections on the screen.

Fig. 6: Identifying DLC-2 Connector

Courtesy of MAZDA MOTORS CORP.

PID/DATA MONITOR CHART

PID Name

Description

Unit

AAT

Indicate the ambient air temperature

°C

AC_REQ

A/C request signal

Off/On

ACCS

A/C relay

Off/On

ALTF

Generator field coil control duty value

APP

Accelerator pedal position

APP1

APP sensor No.1

APP2

APP sensor No.2

APP3

APP sensor No.3

ARPMDES

Target engine speed

RPM

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:28 AM

Page 5

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands