Mazda CX-9 Grand Touring 2007 Manual Download Page 896

Page: 896 / 1056

NO.23 A/C DOES NOT WORK SUFFICIENTLY [MZI-3.5]

DESCRIPTION AND POSSIBLE CAUSES

DIAGNOSTIC PROCEDURE

Inspect the following components for
loose attaching bolts or worn parts:

Cooling fan

Drive belt and pulleys

Generator

Engine mounts

Exhaust system mounts

All items normal?

Yes

Inspect the following systems:

Wheels

ATX

Driveline

Suspension

Readjust or retighten engine mount

installation position.
Service if necessary for other parts.

Verify test results.

{

If normal, return to diagnostic index to service any additional symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [MZI-3.5]

{

If malfunction remains, inspect related Service Bulletins and/or On-line Repair
Information and perform repair or diagnosis.

If vehicle is repaired, troubleshooting completed.

If vehicle is not repaired or additional diagnostic information is not

available, replace the PCM.

(see

PCM REMOVAL/INSTALLATION [MZI-3.5]

A/C DOES NOT WORK SUFFICIENTLY.

DESCRIPTION

A/C compressor magnetic clutch does not engage when the A/C switch is turned
on.

POSSIBLE CAUSE

Improper refrigerant charging amount

Open the A/C magnetic clutch

Open circuit in wiring harness between A/C relay and A/C magnetic clutch

Poor GND of A/C magnetic clutch

Refrigerant pressure switch is stuck open.

A/C relay is stuck open.

Seized A/C compressor

Open circuit in wiring harness between A/C switch and PCM through both

refrigerant pressure switch and A/C amplifier

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:37 AM

Page 79

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands