Mazda CX-9 Grand Touring 2007 Manual Download Page 523

Page: 523 / 1056

connector.

Turn the ignition switch to the ON

position [(Engine off).

Measure the voltage between:

{

CKP sensor terminal A on
the wiring harness side and

battery negative

{

CKP sensor terminal B on
the wiring harness side and

battery negative

Are the voltages between 1-3 V?

Go to Step 8.

INSPECT CKP SENSOR
RESISTANCE

Turn the ignition switch off.

Measure the resistance between
CKP sensor terminal A and B on

the component side.

Is the resistance between 0.25-1
kilohms?

Yes

Go to the next step.

Replace the CKP sensor. Then go to Step
13.

INSPECT CKP WIRING HARNESS

SHIELD CIRCUIT FOR SHORT TO
GROUND

Measure the resistance between:

{

CKP_SHLD assembly
connector wiring harness

side and ground

Is the resistance less than 5 ohms?

NOTE:

The wiring harness shield

protects the CKP signal from
electrical noise and is grounded

at one end, typically near the
PCM.

NOTE:

Perform the following resistance
measurement between the CKP

shield and the ground.

Yes

Go to the next step.

Repair the short circuit. Check for a poor

ground. Then go to Step 13.

INSPECT FOR SHORT BETWEEN

CKP (+) AND CKP (-) IN WIRING
HARNESS

Yes

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:31 AM

Page 176

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands