Mazda CX-9 Grand Touring 2007 Manual Download Page 846

Page: 846 / 1056

NO.6 CRANKS NORMALLY BUT WILL NOT START [MZI-3.5]

DESCRIPTION AND POSSIBLE CAUSES

Does variable valve timing control
function properly?

results.

Is the engine compression correct?

Yes

Inspect the valve timing.

Inspect for cause.

Verify test results.

{

If normal, return to diagnostic index to service any additional symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [MZI-3.5]

{

If malfunction remains, inspect related Service Bulletins and/or On-line Repair

Information and perform repair or diagnosis.

If vehicle is repaired, troubleshooting completed.

If vehicle is not repaired or additional diagnostic information is not
available, replace the PCM.

(see

PCM REMOVAL/INSTALLATION [MZI-3.5]

CRANKS NORMALLY BUT WILL NOT START

DESCRIPTION

The starter cranks engine at normal speed but the engine will not run.

Refer to symptom troubleshooting "

NO.5 ENGINE STALLS

" if this

symptom appears after engine stall.

Fuel is in tank. Battery is in normal condition.

No battery power supply to PCM

Air leakage from intake-air system

Open PCM GND or vehicle body GND

Improper operation of electronic throttle control system

No signal from CKP sensor due to sensor, related wire or incorrect
installation

No signal from CMP sensor due to sensor, related wire or incorrect

installation

Low engine compression

Engine overheating

Vacuum leakage

Erratic signal to ignition coil

Improper air/fuel mixture ratio control

Poor fuel quality

PCV valve malfunction

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:37 AM

Page 29

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands