manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

Fig. 5: Connecting Battery Positive Voltage To Terminal M And Ground

 

PINION GAP INSPECTION 

1. Pull out the drive pinion with the battery positive voltage connected to terminal S and the starter body 

grounded. 

Fig. 6: Connecting Battery Positive Voltage To Terminal S And Grounding Starter Body

 

2. Measure the pinion gap while the drive pinion is extended. 

z

If not as specified, adjust with an adjustment washer (between drive housing front cover and 
magnetic switch).  

Starter pinion gap

  

0 mm {0 in}

  

CAUTION:

z

Applying power for more than 10 s can damage the starter. Do 

not apply power for more than 10 s.  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE Starting System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:28:57 AM

Page 4 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Baja Designs S8 Instructions Manual preview
S8
Brand: Baja Designs Pages: 6
Vaisala MD30 Setup Manual preview
MD30
Brand: Vaisala Pages: 24
Yakima Q46 Installation Instructions preview
Q46
Brand: Yakima Pages: 4
Xblitz G250 User Manual preview
G250
Brand: Xblitz Pages: 16
Trailboss QTHD519L Fitting Instructions Manual preview
QTHD519L
Brand: Trailboss Pages: 8
Thule 1511 Instructions Manual preview
1511
Brand: Thule Pages: 8
Saab 32 025 888 Installation Instructions preview
32 025 888
Brand: Saab Pages: 3
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Brand: muth Pages: 9
Waeco 8885100124 Operating Manual preview
8885100124
Brand: Waeco Pages: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Brand: VBG Pages: 16
BURY CC 9040 Specification preview
CC 9040
Brand: BURY Pages: 2
Great Wall WEY VV5 Service Manual preview
WEY VV5
Brand: Great Wall Pages: 18
WIX WP9378 Installation Instruction preview
WP9378
Brand: WIX Pages: 2
BMW 323Ci Manual preview
323Ci
Brand: BMW Pages: 189
Unex OBU-352EC Quick Start Manual preview
OBU-352EC
Brand: Unex Pages: 30
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Brand: SilverLeaf Electronics Pages: 16
Kia OPTIA hybrid 2020 Features & Functions Manual preview
OPTIA hybrid 2020
Brand: Kia Pages: 54
Huf HUF8432MS Technical Description And User Manual preview
HUF8432MS
Brand: Huf Pages: 6

Brands by name

Popular brands

Load more brands