manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DTC P0462 [MZI-3.5] 

DTC P0462 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

4

VERIFY STORED DTC IN 
INSTRUMENT CLUSTER

 

z

Turn the ignition switch off then 
to the ON position (Engine off).  

z

Verify stored DTCs in instrument 

cluster.  

z

Is other DTCs present?  

Yes

Go to the appropriate DTC inspection. 
(see 

DTC TABLE [INSTRUMENT 

CLUSTER]

 .)

No

Go to the next step.

5

VERIFY TROUBLESHOOTING OF 
DTC P0461 HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 

connectors reconnected.  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Perform the "KOEO/KOER self-

test". 

(See 

KOEO/KOER SELF TEST 

[MZI-3.5]

.) 

z

Is the PENDING CODE for the 
DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

No

Go to the next step.

6

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform the "AFTER REPAIR 

PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTCs present?  

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

DTC P0462

Fuel gauge sender unit circuit low input

DETECTION 
CONDITION

 

z

The PCM monitors the fuel level input communications network message 
for a concern. The test fails if the fuel level input signal is less than the 

minimum allowable calibrated parameter for a specified fuel-fill percentage 
in the fuel tank.  

z

Empty fuel tank  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:33 AM

Page 246 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Brand: Ultra-tow Pages: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Brand: Mercedes-Benz Pages: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Brand: Menabo Pages: 8
Camtree G-51 Instruction Manual preview
G-51
Brand: Camtree Pages: 5
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Brand: Atwood Pages: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Brand: BMW Pages: 21
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Brand: Nuna Pages: 17
BMW M5 2014 Service And Warranty Information preview
M5 2014
Brand: BMW Pages: 38
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Brand: Chevrolet Pages: 412
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Brand: Omix-Ada Pages: 6
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Brand: Subaru Pages: 19
Oldsmobile 2003 Silhouette Owner'S Manual preview
2003 Silhouette
Brand: Oldsmobile Pages: 466
Lincoln NAUTILUS 2022 Owner'S Manual preview
NAUTILUS 2022
Brand: Lincoln Pages: 586
Prorack K374 Manual preview
K374
Brand: Prorack Pages: 14
ROADGEAR RGABM1 User Manual & Fitting Instructions preview
RGABM1
Brand: ROADGEAR Pages: 2
PEUGEOT BOXER 2018 Handbook preview
BOXER 2018
Brand: PEUGEOT Pages: 232
Edelbrock 8135 Installation Instructions preview
8135
Brand: Edelbrock Pages: 4

Brands by name

Popular brands

Load more brands