manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

pump relay connector terminal E 
(harness-side) and body ground.  

z

Is there continuity?  

No

Go to the next step.

8

INSPECT FUEL PUMP CONTROL 
CIRCUIT FOR OPEN CIRCUIT

 

z

Turn the ignition switch off.  

z

Inspect for continuity between fuel 

pump relay terminal E and PCM 
terminal 1V.  

z

Is there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go 

to Step 10.

9

INSPECT FUEL PUMP RELAY

 

z

Inspect the fuel pump relay. 

(see 

RELAY INSPECTION

 .) 

z

Is there any malfunction?  

Yes

Replace the fuel pump relay, then go to 
the next step.

No

Go to the next step.

10

VERIFY TROUBLESHOOTING OF 
DTC P0230 HAS BEEN COMPLETED

z

Verify that all disconnected 

connectors reconnected.  

z

Clear DTC from memory using M-
MDS.  

z

Start the engine.  

z

Perform the "KOEO/KOER self-

test" 

(See 

KOEO/KOER SELF TEST 

[MZI-3.5]

.) 

z

Is same DTC present?  

Yes

Replace the PCM, then go to the next 
step.

No

Go to the next step.

11

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform the "AFTER REPAIR 
PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTCs present?  

Yes

Go to the applicable DTC inspection. 

(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:31 AM

Page 150 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Accel 2020 Installation Instructions preview
2020
Brand: Accel Pages: 2
Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Brand: Cadillac Pages: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Brand: Cadillac Pages: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Brand: Cadillac Pages: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Brand: Cadillac Pages: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Brand: Cadillac Pages: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Brand: Cadillac Pages: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Brand: Cadillac Pages: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Brand: Cadillac Pages: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Brand: Cadillac Pages: 438
Yakima K1188 Instructions Manual preview
K1188
Brand: Yakima Pages: 12
JEHNERT SOUND DESIGN 65400 Assembly Instruction Manual preview
65400
Brand: JEHNERT SOUND DESIGN Pages: 8
Rainbow Experience Series Installation Manual preview
Experience Series
Brand: Rainbow Pages: 19
Yakima K1006 Instructions Manual preview
K1006
Brand: Yakima Pages: 12
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Brand: Kia Pages: 10
Edelbrock For 1985-1992 GM Cars and Trucks 17933 Installation Instructions preview
For 1985-1992 GM Cars and Trucks 17933
Brand: Edelbrock Pages: 4
Bestop WrapAround Windjammer Installation Instructions Manual preview
WrapAround Windjammer
Brand: Bestop Pages: 7
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Brand: BendPak Pages: 104

Brands by name

Popular brands

Load more brands