Mazda CX-9 Grand Touring 2007 Manual Download Page 721 | Manualshive

Page: 721 / 1056

background image

DTC P1501 [MZI-3.5]

DTC P1501 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

DIAGNOSTIC PROCEDURE

DTC P1501 (MZI-3.5) DIAGNOSTIC PROCEDURE

z

Are any DTCs present?

DTC P1501

Vehicle speed sensor (VSS) out of self-test range

DETECTION

CONDITION

z

Indicates that the vehicle speed input signal is out of the self-test range. If
the PCM detects a vehicle speed input signal any time during the self-test,

DTC P1501 is set and the test aborts.

POSSIBLE CAUSE

z

Noise on the vehicle speed input signal from radio frequency

interference/electro magnetic interference

z

External sources, such as ignition wires, the charging circuit, or aftermarket
equipment

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED

z

Has FREEZE FRAME DATA
been recorded?

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the
repair order, then go to the next step.

2

VERIFY RELATED REPAIR

INFORMATION AVAILABILITY

z

Verify related Service Bulletins
and/or on-line repair information

availability.

z

Is any related Service Bulletins

available?

Yes

Perform repair or diagnosis according to

the available Service Bulletins.

z

If the vehicle is not repaired, go to
the next step.

No

Go to the next step.

3

VERIFY STORED DTC IN DSC/RSC
HU/CM

z

Turn the ignition switch to the ON

position (Engine off).

z

Verify stored DTCs in DSC/RSC

HU/CM.

z

Are DTCs stored?

Yes

Go to the appropriate DTC inspection.
(see

ON-BOARD DIAGNOSIS

[DSC/RSC]

.)

No

Go to the next step.

4

VERIFY TROUBLESHOOTING OF
DTC P1501 HAS BEEN

COMPLETED

Yes

Replace the PCM, then go to the next step.
(see

PCM

REMOVAL/INSTALLATION [MZI-
3.5]

.)

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:37 AM

Page 374

© 2005 Mitchell Repair Information Company, LLC.

«
...
719
720
721
722
723
...
»

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Brand: Saab Pages: 75

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: Xblitz Pages: 16

Brand: TrailFX Pages: 6

Brand: Brodit Pages: 2

Brand: Power Fist Pages: 12

Brand: EAL Pages: 7

Brand: Thule Pages: 8

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

Brand: Quadratec Pages: 12

Brand: v.link Pages: 21

Brand: Air Lift Pages: 28

Brand: Dolphin Pages: 16

1500 CLASSIC 2020

Brand: RAM Pages: 360

Brand: Mercedes-Benz Pages: 305

S90 TWIN ENGINE

Brand: Volvo Pages: 662

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands