Mazda CX-9 Grand Touring 2007 Manual Download Page 56

Page: 56 / 1056

MISCELLANEOUS

MISCELLANEOUS LOCATION

Horn Switch

In steering wheel.

Key Reminder Switch

In steering column.

Oil Pressure Switch

Lower left front of engine.

Parking Brake Switch

Top of parking brake assembly.

Power Steering Pressure Switch

Right front side of engine.

Refrigerant Pressure Switch

Right front corner of engine compartment.

Component

Location

Audio Amplifier

Right side of luggage compartment.

Audiopilot Microphone

Behind left side of dash.

Capacitor (2)

Right rear of roof.

Check Connector

Behind right side of dash. See

Fig. 15

Clock Spring

In steering column.

Coil

Behind left side of dash.

Data Link Connector-2

Under lower left side of dash. See

Fig. 30

Diode

Under right side of dash.

Driver-Side Air Bag Module No. 1

In steering wheel.

Driver-Side Air Bag Module No. 2

In steering wheel.

Driver-Side Curtain Air Bag Module

Top of left "D" pillar.

Driver-Side Pre-Tensioner Seat Belt

Base of left "B" pillar.

Driver-Side Side Air Bag Module

Left side of driver's seat back.

Front Power MOS FET

Near front blower motor.

Generator

Left front of engine.

Horn (High)

Left front of engine compartment.

Horn (Low)

Right front of engine compartment.

Ignition Coils No. 1, 2 & 3

Top of right cylinder bank.

Ignition Coils No. 4, 5 & 6

Top of left cylinder bank.

Inverter

Left side of luggage compartment.

Joint Connector (C-36)

Behind left end of dash. See

Fig. 36

Joint Connector (C-37)

Behind left center of dash. See

Fig. 24

Joint Connector (C-38)

Behind center of dash. See

Fig. 19

Keyless Antenna (Exterior, Left/Right Front)

In respective front door.

Keyless Antenna (Exterior, Rear)

Behind center of rear bumper.

Keyless Antenna (Interior, Front Center)

Under middle of dash.

Keyless Antenna (Interior, Rear)

Center front of luggage compartment.

Keyless Antenna (Interior, Right Front)

Under right side of dash.

Microphone

Front center of roof.

Noise Filter

Lower center of liftgate.

2007 Mazda CX-9 Grand Touring

2007 MAZDA CX-9

Microsoft

Sunday, November 15, 2009 9:30:18 AM

Page 5

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands