manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

z

Turn the ignition switch to the ON 

position (Engine off).  

z

Inspect for continuity between 

OCV (LH) terminal B (wiring 
harness-side) and body ground.  

z

Is there continuity?  

No

Go to the next step.

8

INSPECT PCM CONNECTOR FOR 

POOR CONNECTION

 

z

Disconnect the PCM connector.  

z

Inspect for poor connection (such 

as damaged/pulled-out pins, 
corrosion).  

z

Is there any malfunction?  

Yes

Repair or replace suspected part, then go to 

Step 10.

No

Go to the next step.

9

INSPECT OCV (LH) CIRCUIT FOR 

OPEN CIRCUIT

 

z

Turn the ignition switch off.  

z

Measure the resistance between 

the OCV (LH) connector terminal 
B (wiring harness-side) and PCM 

terminal 2BK (wiring harness-
side).  

z

Is there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, Then go 
to the next step.

10

VERIFY TROUBLESHOOTING OF 

DTC P0020 HAS BEEN 
COMPLETED

 

z

Verify that all disconnected 
connectors reconnected.  

z

Turn the ignition switch to the ON 

position (Engine off).  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Start the engine and run it at idle.  

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 

DTC present?  

Yes

Replace the PCM, then go to the next step.

(see 

PCM 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

No

Go to the next step.

11

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform the "AFTER REPAIR 
PROCEDURE". 

Yes

Go to the applicable DTC inspection. 

(See 

DTC TABLE [MZI-3.5]

.)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:29 AM

Page 37 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

N-Com B3 User Instructions And Safety preview
B3
Brand: N-Com Pages: 28
Cequent 10417 Instruction Sheets preview
10417
Brand: Cequent Pages: 9
Whispbar K611W Fitting Instructions Manual preview
K611W
Brand: Whispbar Pages: 77
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Brand: ULTIMATE SPEED Pages: 50
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Brand: Pet Gear Pages: 4
Mitsubishi MIrage 2019 Owner'S Handbook Manual preview
MIrage 2019
Brand: Mitsubishi Pages: 19
Daesung HM-TX-315 User Manual preview
HM-TX-315
Brand: Daesung Pages: 9
Pontiac 2010 Vibe Owner'S Manual preview
2010 Vibe
Brand: Pontiac Pages: 318
Yakima LowRider Manual preview
LowRider
Brand: Yakima Pages: 15
Thule 1809 Instruction Manual preview
1809
Brand: Thule Pages: 4
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Brand: Vauxhall Pages: 95
Porsche 928 GTS 1994 Owner'S Manual preview
928 GTS 1994
Brand: Porsche Pages: 127
Vmac A700308 Installation Manual preview
A700308
Brand: Vmac Pages: 16
Honda 1993 Civic Coupe Owner'S Manual preview
1993 Civic Coupe
Brand: Honda Pages: 201
Fiat FIORINO Owner'S Handbook Manual preview
FIORINO
Brand: Fiat Pages: 220
Ranger design C24-DL Installation Manual preview
C24-DL
Brand: Ranger design Pages: 14
U.S. General 6"OFF ROAD LIGHT 95811 Assembly And Operation Instructions Manual preview
6"OFF ROAD LIGHT 95811
Brand: U.S. General Pages: 7
Honda 2012 Odyssey Owner'S Manual preview
2012 Odyssey
Brand: Honda Pages: 441

Brands by name

Popular brands

Load more brands