manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

Courtesy of MAZDA MOTORS CORP.

 

REMOVAL 

1. Disconnect the negative battery cable.  
2. Remove the following part for easier access. 

1. Remove the Catalytic Converter (WU-TWC) (LH).(see 

EXHAUST SYSTEM 

REMOVAL/INSTALLATION [MZI-3.5]

 .)  

3. Remove in the order indicated in the table.  
4. Install in the reverse order of removal. 

Fig. 18: Identifying CKP Sensor And Connector With Torque Specifications

 

Courtesy of MAZDA MOTORS CORP.

 

CRANKSHAFT POSITION (CKP) SENSOR INSPECTION [MZI-3.5] 

VISUAL INSPECTION 

1. Remove the CKP sensor. (See 

CRANKSHAFT POSITION (CKP) SENSOR 

REMOVAL/INSTALLATION [MZI-3.5]

.)  

2. Verify that there are no metal shavings on the CKP sensor.  
3. Install the CKP sensor. (See 

CRANKSHAFT POSITION (CKP) SENSOR 

REMOVAL/INSTALLATION [MZI-3.5]

.)  

RESISTANCE INSPECTION 

1. Remove the CKP sensor connector.  
2. Measure the resistance between the CKP sensor terminals. 

NOTE:

z

Before performing the following inspection, make sure to follow the 
procedure as indicated in the troubleshooting flowchart. (see HOW TO 

USE THIS MANUAL .)  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Control System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:25:31 AM

Page 20 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Daihatsu Mira Manual preview
Mira
Brand: Daihatsu Pages: 340
Yakima K800 Instructions Manual preview
K800
Brand: Yakima Pages: 8
Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Brand: Jeep Pages: 1311
CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Brand: CITROEN Pages: 2
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Brand: Metra Electronics Pages: 2
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Brand: Mazdaspeed Pages: 8
BrandMotion FLTW-7690 Installation Instructions preview
FLTW-7690
Brand: BrandMotion Pages: 2
Xhorse VVDI User Manual preview
VVDI
Brand: Xhorse Pages: 48
Subaru 1998 Forester Owner'S Manual preview
1998 Forester
Brand: Subaru Pages: 298
Yakima RimROC Instructions Manual preview
RimROC
Brand: Yakima Pages: 12
Axxess AXDSPX-VW1 Installation Instructions Manual preview
AXDSPX-VW1
Brand: Axxess Pages: 16
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Brand: APS Pages: 3
INDIWORK A-LINK2-NTG5 Instruction Manual preview
A-LINK2-NTG5
Brand: INDIWORK Pages: 18
Opel CORSA 2020 Infotainment Manual preview
CORSA 2020
Brand: Opel Pages: 103
Griffin Technology iTrip Bluetooth User Manual preview
iTrip Bluetooth
Brand: Griffin Technology Pages: 6
Mitsubishi Pajero Pinin 1999 Workshop Manual preview
Pajero Pinin 1999
Brand: Mitsubishi Pages: 919
Magneti Marelli Obd Road User Manual preview
Obd Road
Brand: Magneti Marelli Pages: 9
Xforce PR-104 User Manual preview
PR-104
Brand: Xforce Pages: 11

Brands by name

Popular brands

Load more brands