manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

{

MAF sensor terminal C 

(wiring harness-side) and 

PCM terminal 1AJ (wiring 
harness-side)  

{

MAF sensor terminal D 

(wiring harness-side) and 
PCM terminal 1AN (wiring 

harness-side)  

z

Are there continuity?  

7

INSPECT MAF SENSOR SIGNAL 
CIRCUIT FOR SHORT TO 

GROUND

 

z

Turn the ignition switch off.  

z

Disconnect the MAF/IAT sensor 

and PCM connector.  

z

Inspect continuity between 
following circuits: 

{

MAF sensor connector 

terminal D and body ground 

z

Are there continuity?  

Yes

Repair or replace suspected part, then go to 
the Step 10.

No

Go to the next step.

8

INSPECT MAF SENSOR GROUND 
CIRCUIT FOR OPEN CIRCUIT

 

z

Inspect continuity between MAF 
sensor terminal B and body 

ground.  

z

Are there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 
Step 10.

9

INSPECT THE MAF SENSOR

 

z

Inspect the MAF sensor> 

(see 

MASS AIR FLOW (MAF.)

  

SENSOR INSPECTION [MZI-
3.5].) 

z

Are there any malfunction?  

Yes

Replace the MAF/IAT sensor, then go to 
the next step. 

(see 

MASS AIR FLOW 

(MAF)/INTAKE AIR TEMPERATURE 

(IAT) SENSOR 

REMOVAL/INSTALLATION [MZI-
3.5].

 )

No

Go to the next step.

10

VERIFY TROUBLESHOOTING OF 
DTC P0102 HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 
connectors reconnected.  

Yes

Replace PCM, then go to the next step. 
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:29 AM

Page 53 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Brand: iDataLink Pages: 99
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Brand: Kolpin Outdoors Pages: 6
Schartec CR 4 Manual preview
CR 4
Brand: Schartec Pages: 2
Mazda 2008 MX-5 Miata Manual preview
2008 MX-5 Miata
Brand: Mazda Pages: 400
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Brand: Mazda Pages: 12
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Brand: Renault Pages: 183
Quadratec 12057.0261 Installation Manual preview
12057.0261
Brand: Quadratec Pages: 12
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Brand: Mercedes-Benz Pages: 91
Xpresskit DBALL2-HK7 Installation Manual preview
DBALL2-HK7
Brand: Xpresskit Pages: 18
Thule 1061-1-011 Fitting Instructions preview
1061-1-011
Brand: Thule Pages: 3
Quadratec QuadraTop 11051.0415 Installation Manual preview
QuadraTop 11051.0415
Brand: Quadratec Pages: 8
Packard 1948 eight Operating Instructions Manual preview
1948 eight
Brand: Packard Pages: 25
Honda 2009 S2000 Owner'S Manual preview
2009 S2000
Brand: Honda Pages: 268
Huf HUF8432MS Technical Description And User Manual preview
HUF8432MS
Brand: Huf Pages: 6
Pet Gear TL9000 Instruction Manual preview
TL9000
Brand: Pet Gear Pages: 4
Suzuki IGNIS 2022 Series Manual preview
IGNIS 2022 Series
Brand: Suzuki Pages: 570

Brands by name

Popular brands

Load more brands