Mazda CX-9 Grand Touring 2007 Manual Download Page 507

Page: 507 / 1056

DIAGNOSTIC PROCEDURE

DTC P0300 (MZI-3.5) DIAGNOSTIC PROCEDURE

POSSIBLE CAUSE

MAF sensor contamination

Excess air suction in intake air system (between MAF/IAT sensor and
dynamic chamber)

Vacuum hoses damages or improper connection

Fuel pump malfunction

Fuel pressure regulator malfunction

Fuel line clogged

Fuel filter clogged

Fuel runout

Poor quality fuel

Fuel leakage in fuel line

Insufficient compression

Variable valve timing control system improper operation

Purge solenoid valve malfunction

PCV valve malfunction

Related connector and terminal malfunction

Related wiring harness malfunction

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED

Has FREEZE FRAME DATA
been recorded?

Yes

Go to the next step.

Record FREEZE FRAME DATA on the
repair order, then go to the next step.

VERIFY RELATED REPAIR

INFORMATION AVAILABILITY

Verify related Service Bulletins

and/or on-line repair information
availability.

Is any related Service Bulletins

available?

Yes

Perform repair or diagnosis according to the

available Service Bulletins.

If the vehicle is not repaired, go to the

next step.

Go to the next step.

VERIFY RELATED PENDING
CODE OR STORED DTCs

Turn the ignition switch off then
to the ON position (Engine off).

Verify related pending code or

Yes

Go to the appropriate DTC troubleshooting.
(See

DTC TABLE [MZI-3.5]

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:31 AM

Page 160

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands