manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DIAGNOSTIC PROCEDURE 

DIAGNOSTIC PROCEDURE

 

(see AFTER REPAIR PROCEDURE [MZI-3.5] .) 

CAUTION:

z

Disconnecting/connecting quick release connector without 
cleaning it may cause damage to fuel pipe and quick release 

connector. Always clean quick release connector joint area before 
disconnecting/connecting, and make sure that it is free of foreign 

material.  

STEP INSPECTION

RESULTS ACTION

1

Warm up the engine. 

Idle the engine for 

5 min.

  

Is the symptom disappeared?

Yes

Troubleshooting completed. (Cause of 

this symptom is that the idle learning of 
electronic throttle control system is not 

completed.)

No

Go to the next step.

2

Verify the following: 

z

External fuel shut off or 

accessory (such as kill switch, 
alarm)  

z

Fuel quality (such as proper 

octane, contamination, 
winter/summer blend)  

z

No air leakage from intake-air 

system  

z

Proper sealing of intake 
manifold and components 

attached to intake manifold  

z

Ignition wiring  

z

Electrical connections  

z

Fuses  

z

Smooth operation of throttle 

valve  

z

PCM GND circuit (1D, 1J, 1BP, 
1BK).  

 

Are all items normal?

Yes

Go to the next step.

No

Service if necessary. 
Repeat Step 2.

3

Connect the M-MDS to the DLC-2. 

Turn the ignition switch to the ON 

Yes

DTC is displayed:

  

Go to the appropriate DTC inspection. 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:37 AM

Page 40 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Kia Sportage 2018 Features & Functions Manual preview
Sportage 2018
Brand: Kia Pages: 54
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Brand: VDO Pages: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Brand: Wagan Pages: 3
Mini COOPER Owner'S Manual preview
COOPER
Brand: Mini Pages: 20
Right Weigh 221-SK Installation Manual preview
221-SK
Brand: Right Weigh Pages: 16
Dodge Dodge Challenger SRT8®Challenger SRT8 392 2012 Specifications preview
Dodge Challenger SRT8®Challenger SRT8 392 2012
Brand: Dodge Pages: 5
Edelbrock 65932 Installation Instructions preview
65932
Brand: Edelbrock Pages: 2
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Brand: RAM Pages: 174
Fab Fours F2950 Installation Instructions Manual preview
F2950
Brand: Fab Fours Pages: 21
BMW 323Ci Manual preview
323Ci
Brand: BMW Pages: 189
Phonocell 6/821 Mounting Instructions preview
6/821
Brand: Phonocell Pages: 8
SMART EQ forfour 2018 Owner'S Manual preview
EQ forfour 2018
Brand: SMART Pages: 224
Mazda 2011 CX-9 Owner'S Manual preview
2011 CX-9
Brand: Mazda Pages: 605
TracRac TracVan Double Installation Instructions Manual preview
TracVan Double
Brand: TracRac Pages: 6
Valueline SVL-CARCAM11 User Manual preview
SVL-CARCAM11
Brand: Valueline Pages: 40
SoundMax SM-DVR77FHD Instruction Manual preview
SM-DVR77FHD
Brand: SoundMax Pages: 20
Chery SQR477F User Manual preview
SQR477F
Brand: Chery Pages: 163
AVURA MICRO User Manual preview
MICRO
Brand: AVURA Pages: 12

Brands by name

Popular brands

Load more brands