manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DTC P060A, P060C, P061D [MZI-3.5]

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 

HAS BEEN RECORDED

 

z

Has FREEZE FRAME DATA 
been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 

repair order, then go to the next step.

2

VERIFY RELATED REPAIR 
INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

and/or on-line repair information 
availability.  

z

Is any related Service Bulletins 

available?  

Yes

Perform repair or diagnosis according to 
the available Service Bulletins. 

z

If the vehicle is not repaired, go to 

the next step.  

No

Perform PCM reprograming using the M-
MDS, then go to next step.

3

VERIFY TROUBLESHOOTING OF 

DTC P0607 HAS BEEN 
COMPLETED

 

z

Verify that all disconnected 

connectors are reconnected.  

z

Turn the ignition switch to the ON 
position (Engine off).  

z

Clear the DTC from the PCM 

memory using the M-MDS.  

z

Perform "KOEO and KOER self-
test". 

(See 

KOEO/KOER SELF TEST 

[MZI-3.5]

.) 

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 
DTC present?  

Yes

Replace the PCM, then go to the next step.

(see 

PCM 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

No

Go to the next step.

4

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform the "AFTER REPAIR 
PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTCs present?  

Yes

Go to the applicable DTC inspection. 

(see 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:34 AM

Page 288 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Zavoli Bora Technical Instructions And Installation Manual preview
Bora
Brand: Zavoli Pages: 26
Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Brand: Kia Pages: 419
AMP Research 75135-01A Installation Manual preview
75135-01A
Brand: AMP Research Pages: 12
Havis-Shields Half Size Trunk Box Organizer C-TBO-CV Installation Instructions preview
Half Size Trunk Box Organizer C-TBO-CV
Brand: Havis-Shields Pages: 1
Volvo S60 2012 Quick Manual preview
S60 2012
Brand: Volvo Pages: 8
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Brand: PullRite Pages: 10
TATA Motors Indigo MANZA QUADRAJET 90 Owner'S Manual & Service Book preview
Indigo MANZA QUADRAJET 90
Brand: TATA Motors Pages: 10
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Brand: Cadillac Pages: 34
Saab 2000 9-5 2.3 Turbo Ecopower Owner'S Manual preview
2000 9-5 2.3 Turbo Ecopower
Brand: Saab Pages: 256
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Brand: Blue Ox Pages: 9
BMW 316I Owner'S Handbook Manual preview
316I
Brand: BMW Pages: 177
Volvo FH 6X2 Specifications preview
FH 6X2
Brand: Volvo Pages: 3
FACTORY UTV Dual Clamp Spare Tire Mount Installation Manual preview
Dual Clamp Spare Tire Mount
Brand: FACTORY UTV Pages: 2
Prorack K319 Fitting Instructions Manual preview
K319
Brand: Prorack Pages: 13
Classic Accessories Quad Gear 18-029-010401-00-SC Instructions preview
Quad Gear 18-029-010401-00-SC
Brand: Classic Accessories Pages: 4
Teletrac Prism TM450 Installation Manual preview
Prism TM450
Brand: Teletrac Pages: 12
Ratio Electric HOME BOX SMART Manual preview
HOME BOX SMART
Brand: Ratio Electric Pages: 16
Fab Fours Y1351T Installation Instructions Manual preview
Y1351T
Brand: Fab Fours Pages: 16

Brands by name

Popular brands

Load more brands