Mazda CX-9 Grand Touring 2007 Manual Download Page 707

Page: 707 / 1056

CONNECTION

Disconnect the CKP sensor

connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Is there any malfunction?

Go to the next step.

INSPECT CKP SENSOR

Inspect the CKP sensor.

(see

CRANKSHAFT POSITION

(CKP) SENSOR INSPECTION
[MZI-3.5].

)

Is there any malfunction?

Yes

Replace the CKP sensor, then go to Step
11.

(see

CRANKSHAFT POSITION (CKP)

SENSOR
REMOVAL/INSTALLATION [MZI-

3.5].

)

Go to the next step.

INSPECT CMP SENSOR
CONNECTOR FOR POOR

CONNECTION

Disconnect the CMP sensor

connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Is there any malfunction?

Yes

Repair or replace suspected part, then go to
Step 11.

Go to the next step.

INSPECT CMP SENSOR

Inspect the CMP sensor.

(see

CAMSHAFT POSITION

(CMP) SENSOR INSPECTION
[MZI-3.5].

)

Is there any malfunction?

Yes

Replace the CMP sensor, then go to Step
11.

(see

CAMSHAFT POSITION (CMP)

SENSOR

REMOVAL/INSTALLATION [MZI-

3.5].

)

Go to the next step.

INSPECT PCM CONNECTOR FOR
POOR CONNECTION

Disconnect the PCM connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Are any malfunction?

Yes

Repair or replace suspected part, then go to
the next step.

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:36 AM

Page 360

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands