Mazda CX-9 Grand Touring 2007 Manual Download Page 246

Page: 246 / 1056

Fig. 83: Identifying No. 1 Engine Mount Bolt "C"

Courtesy of MAZDA MOTORS CORP.

2. Remove the No.1 engine mount bracket bolts A and B as shown.

Fig. 84: Identifying Engine Mount No. 1 Bracket Bolts A And B

Courtesy of MAZDA MOTORS CORP.

3. Position the coolant reserve tank out of the way. (see

COOLANT RESERVE TANK

REMOVAL/INSTALLATION [MZI-3.5]

4. Remove the following parts to install the SST.

1. The windshield wiper arm and blade. (see

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

2. The cowl grille. (see

COWL GRILLE REMOVAL/INSTALLATION

3. The cowl panel. (see

COWL PANEL REMOVAL/INSTALLATION

4. The air cleaner. (see

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-3.5]

5. The front cooler pipe installation bolt (position the front cooler pipe out of the way.).

NOTE:

Do not remove the No.1 engine mount rubber from the front

crossmember.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 55

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands