Mazda CX-9 Grand Touring 2007 Manual Download Page 878

Page: 878 / 1056

DIAGNOSTIC PROCEDURE

POSSIBLE CAUSE

Improper engine compression

Exhaust system clogging

WARNING:

The following troubleshooting flow chart contains fuel system diagnosis
and repair procedures. Read following warnings before servicing fuel

system:

Fuel vapor is hazardous. It can easily ignite, causing serious injury

and damage. Always keep sparks and flames away from fuel.

Fuel line spills and leakage are dangerous. Fuel can Ignite and
cause serious injuries or death and damage. Fuel can also irritate

skin and eyes. To prevent this, always complete "BEFORE REPAIR
PROCEDURE" and "AFTER REPAIR PROCEDURE" described in

this manual.

(see BEFORE REPAIR PROCEDURE [MZI-3.5] .)

(see AFTER REPAIR PROCEDURE [MZI-3.5] .)

CAUTION:

Disconnecting/connecting quick release connector without
cleaning it may cause damage to fuel pipe and quick release

connector. Always clean quick release connector joint area before
disconnecting/connecting, and make sure that it is free of foreign

material.

STEP

INSPECTION

RESULTS

ACTION

Inspect for the following:

Air cleaner element for

contamination

ATF level

Fuel quality

Coolant level

Brake dragging

Are all items normal?

Yes

Go to the next step.

Service if necessary.
Repeat Step 1.

Connect the M-MDS to the DLC-2.
Turn the ignition switch to the ON

position (Engine off).

Yes

DTC is displayed:

Go to the appropriate DTC inspection.

(see

DTC TABLE [MZI-3.5]

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:37 AM

Page 61

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands