Mazda CX-9 Grand Touring 2007 Manual Download Page 342 | Manualshive

Page: 342 / 1056

background image

Fig. 12: Identifying SST On Bolts, Nuts, And Plate With Specifications

Courtesy of MAZDA MOTORS CORP.

8. Mount the engine on the

SST

(engine stand).

Fig. 13: Mounting Engine On SST (Engine Stand)

Courtesy of MAZDA MOTORS CORP.

Dismounting

1. Dismount in the reverse order of mounting.

OIL PAN REMOVAL NOTE

1. Install two of the oil pan bolts temporarily into the two threaded holes in the oil pan.
2. Alternately tighten the two bolts one turn at a time until the oil pan-to-cylinder block seal is released.
3. Remove the oil pan.

WARNING:

z

Self-locking brake system of the engine stand may not be
effective when the engine is held in an unbalanced position.

This could lead to sudden, rapid movement of the engine and

mounting stand handle and cause serious injury. Never keep
the engine in an unbalanced position, and always hold the

rotating handle firmly when turning the engine.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Lubrication (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:32:53 AM

Page 11

© 2005 Mitchell Repair Information Company, LLC.

«
...
340
341
342
343
344
...
»

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Brand: JETBAG Pages: 44

Brand: Daihatsu Pages: 43

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: muth Pages: 10

Brand: Mazda Pages: 13

Brand: Inbay Pages: 20

Brand: Opel Pages: 254

Brand: Würth Pages: 36

1966 Spider 105

Brand: Alfa Romeo Pages: 46

Brand: MAcarbon Pages: 3

Brand: Acura Pages: 7

Brand: Scosche Pages: 12

Brand: Menabo Pages: 8

Brand: APS Pages: 4

Brand: Hama Pages: 39

ChargePoint CT500-DSTAND

Brand: Coulomb Technologies Pages: 26

Aura Mobile BT MCP-2014

Brand: Spracht Pages: 2

Brand: Metra Electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands