Mazda CX-9 Grand Touring 2007 Manual Download Page 284

Page: 284 / 1056

Electrical load on: 630-730 rpm

Power steering oil pump operation: 600-700 rpm

A/C and heater operation: 570-850 rpm [-40-49°C {-40-120°F}]

IDLE MIXTURE INSPECTION

1. Perform "Engine Tune-up Preparation". (See

ENGINE TUNE-UP PREPARATION

2. Verify that the idle speed and ignition timing are within the specification. (See

IGNITION TIMING

INSPECTION

.) (See

Idle Speed Inspection

3. Insert an exhaust gas analyzer into the tailpipe.
4. Verify that the CO and HC concentrations are within the specified regulation.

If not within the regulation, refer to "ENGINE SYMPTOM TROUBLESHOOTING". (see

ENGINE SYMPTOM TROUBLESHOOTING [MZI-3.5]

Idle mixture

HC concentration: Within the regulation

CO concentration: Within the regulation

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:28 AM

Page 93

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands