manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DTC P1650 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

Fig. 13: PSP Switch Circuit Diagram

 

Courtesy of MAZDA MOTORS CORP.

 

DIAGNOSTIC PROCEDURE 

DTC P1650 (MZI-3.5) DIAGNOSTIC PROCEDURE

 

DTC P1650

PSP switch out of self-test range

DETECTION 
CONDITION

 

z

In the KOEO self-test, this DTC indicates the PSP input to the PCM is high. 

In the KOER self-test, this DTC indicates the PSP input did not change 
state.  

POSSIBLE CAUSE

 

z

The steering wheel must be turned during KOER self-test  

z

PSP switch malfunction  

z

Open circuit between PSP switch terminal A and PCM terminal 2I  

z

Short to ground circuit between PSP switch terminal A and PCM terminal 2I 

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 
HAS BEEN RECORDED

 

z

Has FREEZE FRAME DATA 

been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 

repair order, then go to the next step.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:37 AM

Page 381 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Jeep Compass Overview Manual preview
Compass
Brand: Jeep Pages: 25
Carefree Slideout Cover Service Manual preview
Slideout Cover
Brand: Carefree Pages: 12
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Brand: Metra Electronics Pages: 2
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Brand: Curt Manufacturing Pages: 6
Safe Fleet RVS-082550 Instruction Manual preview
RVS-082550
Brand: Safe Fleet Pages: 11
Camec 042374 User Manual preview
042374
Brand: Camec Pages: 19
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Brand: STARLANE Pages: 24
Jaeger 21360508 Fitting Instructions Manual preview
21360508
Brand: Jaeger Pages: 13
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Brand: IOGear Pages: 38
Master Tailgaters MR-43E2DVR1 User Manual preview
MR-43E2DVR1
Brand: Master Tailgaters Pages: 10
Sintrones SBOX-2320 User Manual preview
SBOX-2320
Brand: Sintrones Pages: 55
Whispbar K723W Fitting Instructions Manual preview
K723W
Brand: Whispbar Pages: 77
BrandMotion 212IFD001N User Manual preview
212IFD001N
Brand: BrandMotion Pages: 12
LedGlow Advanced Million Color Installation Instructions preview
Advanced Million Color
Brand: LedGlow Pages: 4
Buick 2014 LaCrosse Manual preview
2014 LaCrosse
Brand: Buick Pages: 112
Kleinn Air Horns RNGR-102-1/220 Installation Manual preview
RNGR-102-1/220
Brand: Kleinn Air Horns Pages: 33
Front Runner TBRA020 Quick Start Manual preview
TBRA020
Brand: Front Runner Pages: 7
ABB InCharge Terra AL2-40-240-T1-WC1R Installation Manual preview
InCharge Terra AL2-40-240-T1-WC1R
Brand: ABB Pages: 39

Brands by name

Popular brands

Load more brands