Mazda CX-9 Grand Touring 2007 Manual Download Page 627

Page: 627 / 1056

DTC P0603 [MZI-3.5]

DTC P0603 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

availability.

Is any related Service Bulletins

available?

Reprogram the vehicle ID using the M-
MDS, then go to the next step.

VERIFY TROUBLESHOOTING OF
DTC P0602 HAS BEEN

COMPLETED

Verify that all disconnected
connectors are reconnected.

Turn the ignition switch to the ON

position (Engine off).

Clear the DTC from the PCM

memory using the M-MDS.

Perform the "KOEO and KOER
self-test".

(See

KOEO/KOER SELF TEST

[MZI-3.5]

Retrieve DTCs using the M-MDS.

Is the PENDING CODE for this

DTC present?

Yes

Replace the PCM, then go to the next step.
(see

PCM

REMOVAL/INSTALLATION [MZI-
3.5]

Go to the next step.

VERIFY AFTER REPAIR
PROCEDURE

Perform the "After Repair
Procedure".

(See

AFTER REPAIR

PROCEDURE [MZI-3.5]

Are any DTCs present?

Yes

Go to the applicable DTC inspection.
(See

DTC TABLE [MZI-3.5]

Troubleshooting completed.

DTC P0603

PCM keep alive memory (KAM) error

DETECTION

CONDITION

Indicates the PCM has experienced an internal memory concern. However, there a

external items that can cause this DTC.

POSSIBLE CAUSE

Reprogramming

Battery terminal corrosion

Open circuit between battery positive terminal and PCM terminal 1BB

Connector or terminal malfunction

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:34 AM

Page 280

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands